- Adjustable between three charging rates
- Charge while riding using a dynamo and The Plug III
- Charges at speeds as low as 8 km/h
- Useable as an LED flashlight or backup bicycle rear light while on the road with SOS flash-function built-in
- Latest generation rechargeable battery cells provide over 10 Wh power capacity which results in approximately 4 hours of use at USB specification
- Acts as a buffer between a device and the Plug allowing the use of high-drain devices
Smart Power Pack II
More detailed information can be downloaded here.
Your questions - Our answers
The SPP is a mobile outdoor USB buffer battery designed for bicycle hub dynamo power supplies, especially the Plug III. It can be used to charge many electronic devices such as GPS devices, MP3 players or smartphones, which can be powered via a USB cable. It also has an integrated flashlight with the LED Smart functions, taillight, lamp and SOS light, which work for up to 3 days.
A USB power supply powered by a dynamo hub does not provide a constant supply during slower uphill riding, or frequent traffic light stops in city traffic. This often results in device charging prompts as the charge cycle is frequently interrupted. To prevent this, the SPP is connected between the power source (eg. Plug III) and your device. Both USB ports can be used simultaneously, enabling simultaneous charging and discharging.
The SPP has been developed for hikers, adventurers and especially cyclists who carry electronic devices on the road and also want to charge them. Of course, it can also be used on its own as a battery bank, but it reaches its full potential when used in combination with the Plug III dynamo power supply so it can be charged on the move. The intended use is cycling of all kinds - there are no restrictions regarding the range of use, i.e. it can be used on trekking, touring, city and road bikes as well as on mountain bikes.
The advantages of the SPP compared to conventional power banks is the ability to charge and discharge simultaneously, and accept the inconsistent power generated by a dynamo hub. The unique Flexcharge system allows it to do this even at very low speeds. In addition, its robust construction and the helpful Smart functions reduce the amount of equipment you need, make it ideal for outdoor use - especially on bicycle tours.
The Flexcharge system offers the ability to control the current with which the SPP is charged. It is possible to charge the SPP at speeds starting from 7km/h when riding slowly or uphill, or set to charge more quickly when riding at higher speeds. This allows you to make the best use of the power provided by the dynamo. The settings to control the Flexcharge system can be found in the operating instructions.
The SPP should not be used in heavy rain without a cap, as the USB socket can get wet when the cable is plugged in. Do not use the SPP at extreme temperatures above 50°C or below -10°C, as this can significantly shorten the battery life and irreparably damage the cell. The optimum operating temperature is between 10°C and 35°C.
You can charge your SPP via its Micro USB port with a Micro USB cable to any USB power source that complies with the USB specifications (USB 220V power supply, PLUG III, PC-USB sockets etc.). You should set the Flexcharge rate to match that of your charge power source – if they do not match, the SPP may not charge at the optimal speed (or at all).
The SPP is protected against splashing water (e.g. light rain) by a closed protective cap. The connector itself is not pretected when a device is plugged in. Avoid high pressure and streaming water at all costs.
Your Flexcharge system may be set to charge with too much current. If your SPP only charges at over 20 Km/h, the quick-charge mode is probably activated. Select the Flexcharge mode with a lower charge current. You can find the instructions for adjusting the settings in the product manual.
Your Flexcharge system may be set to a low charge speed normally used for charging from a dynamo hub. When plugged into a wall socket, select the quick charge mode to 900mA. You can find the instructions for adjusting the settings in the product manual.
In this case please contact our support team.
Theoretically, the SPP can be used in combination with any device that is capable of external USB operation or can even be charged via USB and operated simultaneously. This should be the majority of mobile phones, MP3 and GPS devices. Due to the large number of devices it is not possible for us to test all devices. Please check with your device manufacturer the exact behavior when connecting to an external USB power supply.
Yes, you can use it with an iPhone without a special charging cable. The exact functionality of your smartphone depends on the power requirements of your device. If this does not exceed 1.5A, your smartphone should charge. Due to the large number of devices it is not possible for us to test all devices. Please check with your device manufacturer the exact behavior when connecting to an external USB power supply.
Yes, as long as his device does not require more than the maximum output current of the SPP of 1500mA. But keep in mind that the battery of a tablet is much larger and you will get a very small charge increase.
Yes, but this requires a USB multiple connector. In addition, the total power consumption of the connected devices must not exceed the provided power of the SPP of 7,5W.
The SPP has an integrated LED flashlight with a white LED on the front and red LEDs on the back. It also has an adjustable charging current, a charge status display and an adjustable "Auto on/off" function
For the flashlight there are the operating modes "Flashlight", "Taillight" and "SOS". Please refer to the instructions for the setting options.
The lithium-ion battery of the SPP has a capacity of ≥ 3200mAh at a nominal voltage of 3.7V.
The SPP has a maximum output power of 7.5W, which corresponds to a current of 1500mA at the USB nominal voltage of 5V.
No. To charge the SPP you need a standard Micro USB cable, and the output uses a standard type A USB socket. The outgoing cable is determined by your device.
The Flexcharge system charges the SPP from an input current of 100mA. This is already provided by Plug III from a speed of approx. 7 Km/h. Please refer to the instructions for the setting options.
You can adjust the Flexcharge system according to your needs. Please see the manual.
No. The SPP has integrated charging electronics, so overcharging or deep discharge is impossible. The charging display also shows the current charge level.
The SPP has a charge status LED which indicates the charge status by colour gradation. Two rear LEDs as well as one front LED are also illuminated during the charging process.
The SPP can be used on hybrid, trekking, touring, city and road bikes as well as mountain bikes. The X-Mount makes mounting on possible on virtually all types of bikes. This bracket is available as an optional accessory.
Yes, thanks to the X-Mount mount, the SPP can be mounted in seconds without any special skills or tools.
The best way to mount the SPP to your bike is with our X-Mount mount. This makes it possible to attach the SPP to various points on the bicycle within seconds, without screws, and to remove it just as quickly.
YOUR PERSONAL CONTACT
ASK US ANYTHING
Our customer focus is not only reflected in the development of first-class bicycles. We pride ourselves on being available to you before, during and after your purchase. Personal, competent and fast.Get in Touch